- Can you have 2 routers?
- What are the advantages of a hub?
- What is the difference between a hub and a layer 2 switch?
- Can I use a router as a hub?
- What is the difference between hub switch router and bridge?
- How do I know if my switch is layer 2 or 3?
- What layer is Hub?
- Why are hubs obsolete today?
- What is the main difference between hub and switch?
- What is Layer 2 switch used for?
- Is a hub better than a router?
- Why do hubs work at physical layer?
- What is the purpose of a hub?
- Are hubs layer 2?
- Do Layer 2 switches use IP addresses?
- Why is switch preferred to hub?
- Is VLAN a Layer 2?
Can you have 2 routers?
Yes, it is possible to use two (or even more than two) routers on the same home network.
The benefits of a two-router network include: …
Improved wireless reach (signal range): Adding a second wireless router to an existing Wi-Fi network can extend its reach to accommodate far away devices..
What are the advantages of a hub?
Benefits or advantages of Hubs ➨It can extend total distance of the network. ➨It does not affect performance of the network seriously. ➨It is cheaper. ➨It can connect different media types.
What is the difference between a hub and a layer 2 switch?
The main difference between a hub and a layer 2 switch is their complexity. A hub is a very simple device that does virtually no processing and simply forwards the packets it receives. … A layer 2 switch also does this but only when it does not have an entry for the destination.
Can I use a router as a hub?
By simply running an Ethernet cable between your old router to your current one (run a wire from one of the available LAN ports on your active router to the WAN-in LAN ports on the old router), you can repurpose it as a network hub/switch.
What is the difference between hub switch router and bridge?
The key difference between hubs, switches and bridges is that hubs operate at Layer 1 of the OSI model, while bridges and switches work with MAC addresses at Layer 2. Hubs broadcast incoming traffic on all ports, whereas bridges and switches only route traffic towards their addressed destinations.
How do I know if my switch is layer 2 or 3?
When switches allow for IP-based routing, VLANs, etc, they have layer 3 capabilities, e.g. routing. Almost all “smart” switches and all “managed” switches are layer 3. All “unmanaged” switches are layer 2.
What layer is Hub?
physical layerA hub works at the physical layer (layer 1) of the OSI model. A repeater hub also participates in collision detection, forwarding a jam signal to all ports if it detects a collision.
Why are hubs obsolete today?
Hubs let data be brodcasted to any device connected to it, which is a large security risk, therefore they have been replaced with switches. Hubs let data be brodcasted to any device connected to it, which is a large security risk, therefore they have been replaced with switches.
What is the main difference between hub and switch?
What Is the Difference? A hub works on the physical layer (Layer 1) of OSI model while Switch works on the data link layer (Layer 2). Switch is more efficient than the hub. A switch can join multiple computers within one LAN, and a hub just connects multiple Ethernet devices together as a single segment.
What is Layer 2 switch used for?
A layer 2 switch is a type of network switch or device that works on the data link layer (OSI Layer 2) and utilizes MAC Address to determine the path through where the frames are to be forwarded. It uses hardware based switching techniques to connect and transmit data in a local area network (LAN).
Is a hub better than a router?
A hub and a router are both electronic devices used in computer systems networking. A router is a more sophisticated device with both hardware and software that is used to connect multiple area networks (LANs and WANs), or two or more logical subnets. See also Hub vs….Comparison chart.HubRouterPorts4/12 ports2/4/5/815 more rows
Why do hubs work at physical layer?
10BaseT hubs are also Physical layer devices. Technically, they’re known as multiport repeaters because the purpose of a hub is to regenerate every packet received on any port on all of the hub’s other ports. Repeaters and hubs don’t examine the contents of the packets that they regenerate.
What is the purpose of a hub?
A hub, also called a network hub, is a common connection point for devices in a network. Hubs are devices commonly used to connect segments of a LAN. The hub contains multiple ports. When a packet arrives at one port, it is copied to the other ports so that all segments of the LAN can see all packets.
Are hubs layer 2?
Hubs are layer 1 devices,Hubs are just splitters. … Hubs unlike switches do not have any intelligence and do not process packets in any way. They just send all the data received on the hub out to all the other active ports on the hub with the exception of the incoming port.
Do Layer 2 switches use IP addresses?
Explanation:A switch, as a Layer 2 device, does not need an IP address to transmit frames to attached devices. However, when a switch is accessed remotely through the network, it must have a Layer 3 address. … Routers, not switches, function as default gateways.
Why is switch preferred to hub?
A switch is preferred over a hub because a switch will only send message to device that needs or request it.
Is VLAN a Layer 2?
A virtual LAN (VLAN) is any broadcast domain that is partitioned and isolated in a computer network at the data link layer (OSI layer 2). LAN is the abbreviation for local area network and in this context virtual refers to a physical object recreated and altered by additional logic.