Quick Answer: Why Would A Floating Static Route Be Configured With An Administrative Distance?

Which command is used to configure ipv6 static routes?

In Cisco Routers, IPv6 static routes can be configured using the following Cisco IOS command ipv6 route from Cisco IOS global configuration mode..

How does a static route work?

Static routes are manually added to a routing table through direct configuration. Using a static route, a router can learn about a route to a remote network that is not directly attached to one of its interfaces.

What is the next hop router’s IP address?

More specifically, next hop is an IP address entry in a router’s routing table, which specifies the next closest/most optimal router in its routing path. Every single router maintains its routing table with a next hop address, which is calculated based on the routing protocol used and its associated metric.

How do you create a floating static route?

To create floating static route(s) you will create identical routes that already exist which go to R2 through the main frame-relay link to traverse the point to point link which have a higher administrative distance so as long as Serial0/0 is up traffic will take that path but if Serial0/0 fails the router will re- …

What happens to a static route entry?

What happens to a static route entry in a routing table when the outgoing interface associated with that route goes into the down state? The static route is removed from the routing table. The router polls neighbors for a replacement route. … The router automatically redirects the static route to use another interface.

Which routing protocol has the lowest administrative distance?

EIGRPThe correct answer is: So EIGRP has e smallest default administrative distance of IBGP, OSPF,IS-IS, EIGRP and RIP.

What does IP route 0.0 0.0 mean?

Explanation. IP route 0.0. 0.0 0.0. 0.0 Fa0/0 in plain English means “packets from any IP address with any subnet mask get sent to Fa0/0”. Without any other more specific routes defined, this router will send all traffic to Fa0/0.

What is a characteristic of a floating static route?

Explanation: A floating static route is a static route with an administrative distance higher than that of another route already in the routing table. If the route in the table disappears, the floating static route will be put into the routing table in its place.

Why would a floating static route be configured?

Floating static routes are static routes that have an administrative distance greater than the administrative distance of another static route or dynamic routes. They are very useful when providing a backup to a primary link, as shown in Figure 2-66.

What is the administrative distance of a static route?

On Cisco routers, static routes have an administrative distance of 1, making them preferred over routes issued by a dynamic routing protocol. The administrative distance is a value that is always only referenced by the local router itself. The administrative distance is not advertised on the network.

Which type of static route that is configured on a router uses only?

11. Which type of static route that is configured on a router uses only the exit interface? When only the exit interface is used, the route is a directly connected static route. When the next-hop IP address is used, the route is a recursive static route.

What are two reasons why an administrator might choose to use static routing?

What are two reasons why an administrator might choose to use static routing rather than dynamic routing? (Choose two.)Static routing is easier to maintain in large networks.Static routing is more secure.Static routing is more scalable.Static routing uses less router processing and bandwidth.More items…•

Which statement about static and dynamic routes is true?

Static routes tell the router how to forward packets to networks that are not directly connected, while dynamic routes tell the router how to forward packets to networks that are directly connected.

What is the difference between metric and administrative distance?

A routing protocol uses a metric to determine which route to include in the routing table when it has two available routes to the same destination. As opposed to administrative distance, metrics involve a single routing protocol. … They have nothing to do with multiple sources for routes.

What is standard static route?

A default static route is a route that matches all packets. A default route identifies the gateway IP address to which the router sends all IP packets that it does not have a learned or static route for. A default static route is simply a static route with 0.0. 0.0/0 as the destination IPv4 address.