- What does IA mean in the routing table?
- What is an example of EGP?
- WHAT IS routing protocol code?
- How do I display the ipv4 routing table?
- How do I display a routing table in Cisco?
- How do I check my routing?
- What routing protocols are RIP and RIPv2?
- What is the purpose of a routing protocol?
- What is the command to list all the routes in a routing table?
- What is Genmask in routing table?
- What is a routing issue?
- How do I find my IP route?
- How do you write a routing table?
- What does C mean in routing table?
- What does R mean in routing table?
- What is the administrative distance of a static route?
- Why would you display the IP routing table?
- What command issued from a command prompt will display the routing table in Windows?
What does IA mean in the routing table?
Inter-area routesThese routes are routes that are in the same area.
Inter-area routes are the “O IA” routes that are learned in different areas.
If you have 2 areas, area 0 and 1, the routes that are originated in Area 0 and learned by other routers in Area 0 are intra-area routes..
What is an example of EGP?
The most high profile example of an EGP is the internet itself. The routing table of the EGP protocol includes known routers, route costs, and network addresses of neighboring devices.
WHAT IS routing protocol code?
Routing protocol code identifies by which routing protocol each route was learned. Study Notes: Common routing protocol codes include: C – connected. S – static.
How do I display the ipv4 routing table?
Step 1: Record your PC information. On your PC, open a command prompt window and type the ipconfig /all command to display the following.Step 2: Display the routing tables. In a command prompt window type the netstat –r (or route print) command to display the host routing table.Step 3: Examine the Interface List.
How do I display a routing table in Cisco?
The show ip route command is used to show the router’s routing table. This is the list of all networks that the router can reach, their metric (the router’s preference for them), and how to get there. This command can be abbreviated sh ip ro and can have parameters after it, like sh ip ro ospf for all OSPF routes.
How do I check my routing?
There are two numbers you’ll need to provide. Your bank routing number is a nine-digit code that’s based on the U.S. Bank location where your account was opened. It’s the first set of numbers printed on the bottom of your checks, on the left side. You can also find it in the U.S. Bank routing number chart below.
What routing protocols are RIP and RIPv2?
distance vector routing protocolsRIP and RIPv2 are distance vector routing protocols. OSPF and IS-IS are link state.
What is the purpose of a routing protocol?
A routing protocol specifies how routers communicate with each other to distribute information that enables them to select routes between any two nodes on a computer network.
What is the command to list all the routes in a routing table?
Use the -p option with the print command to view the list of registered persistent routes. The destination specifies the network destination of the route. The destination can be an IP network address, an IP address for a host route, or a default route.
What is Genmask in routing table?
Genmask : The netmask for the destination net; 255.255. 255.255 for a host destination and 0.0. 0.0 for the default route. It’s called ‘genmask’ because it shows the ‘generality’ (i.e. the netmask) of the route.
What is a routing issue?
Routing problems tend to emerge when you’re first setting up a new piece of network equipment, and when something has failed. Usually routing problems are caused by some sort of configuration or design error.
How do I find my IP route?
Use the show ip route EXEC command to display the current state of the routing table.
How do you write a routing table?
Each entry in the routing table consists of the following entries:Network ID: The network ID or destination corresponding to the route.Subnet Mask: The mask that is used to match a destination IP address to the network ID.Next Hop: The IP address to which the packet is forwarded.Outgoing Interface: … Metric:
What does C mean in routing table?
directly connected networkLike IPv4, a ‘C’ next to a route indicates that this is a directly connected network. An ‘L’ indicates the local route. In an IPv6 network, the local route has a /128 prefix. Local routes are used by the routing table to efficiently process packets with a destination address of the interface of the router.
What does R mean in routing table?
Identifies that the route was learned dynamically from another router using the EIGRP routing protocol. O: Identifies that the route was learned dynamically from another router using the OSPF routing protocol. R: Identifies that the route was learned dynamically from another router using the RIP routing protocol.
What is the administrative distance of a static route?
On Cisco routers, static routes have an administrative distance of 1, making them preferred over routes issued by a dynamic routing protocol. The administrative distance is a value that is always only referenced by the local router itself. The administrative distance is not advertised on the network.
Why would you display the IP routing table?
Description. Use the display ip routing-table command to display brief information about active routes in the routing table. … This command displays detailed information about all active and inactive routes, including the statistics of the entire routing table and information for each route.
What command issued from a command prompt will display the routing table in Windows?
routeWindows has a command-line tool for view the routing table. It is called “route.”